Trolling Motor Shaft Length

Of shaft to stow. 09122015 Determining the proper trolling motor shaft length is one of the key aspects of finding the right motor for your boat.

Pin On Products

This length may vary by an inch or two but the rated motor shaft length may be round to the closest number.

Trolling motor shaft length. Im about ready to upgrade my trolling motor from the tiller version to an i-Pilot Terrova. The rule of thumb is that the top of the motor section should be submerged 12. Shaft Length for Transom Mount Motors.

Add an additional 5 inches to the sum above. If you decide to place the trolling motor on the bow youll require a long shaft length the reason being that the bow is always a bit higher when compared to the boat. Typically the standard shaft length on the market is 42 inches.

Below the water line in your specific fishing conditions. Determine the motor shafts length. The center of the motor section should be at least 12 inches below the waterline.

First it is important to ensure the propeller rem. Power from electric trolling motors is rated in pounds of thrust rather than horsepower. You can learn more about choosing the correct shaft length here.

I just upgraded to a MK Terrova so new that I havent mounted it yet. 03082020 You have to measure from the bottom of the motor head to the propeller housing to measure the shaft length on a rolling engine. Choosing the correct shaft length for your trolling motor is important for several reasons.

It will help ensure that the motors shaft is long enough to keep the propeller submerged at least 12. Tips for Measuring Trolling Motor Shaft Length. If you frequently fish or boat in rough waters you may even want your motor a little bit deeper.

30 shaft for transoms up to 10 high. Post Dec 21 2017 1 2017-12-21T2105. 25012018 Posted January 25 2018.

Meanwhile if you are steering a hand-controlled motor while standing up you should extend the length of the transom by 12. Steering will be less uncomfortable and difficult. And have less issues with another 6.

If you want a trolling motor that mounts on your transom things are usually less complicated. MotorGuides shafts come in various lengths ranging from 30 to 72. The standard shaft length is 42.

15012018 Choosing the correct trolling motor shaft length is important so that the anglers electric motor does not cavitate creating fish-spooking noise. If primarily inshore in relatively calm waters for the majority of use stick with the 54. Use a tape measure and determine the motor shafts length by measuring from the base of the head down to the propeller housing in inches.

MotorGuide has been designing and manufacturing trolling motors for over 50 years. 27022020 Also Know how long should the shaft be on my trolling motor. If the waves get over 18.

Pounds of thrust and voltage. MotorGuide Technology and Features. This is because most boats have transoms at a similar height.

Is standard shaft length for glass bass boats with standard freeboard height like yours. For rough motor fishing you should extend the recommended length with 5. The ideal shaft length will place the motor and propeller approximately 1 foot below the water.

Minn Kota recommends the following shaft length for different transom heights. What caused the shaft to fall apart at the collar. If your trolling motor has controls that you operate from a standing position the shaft.

This will ensure the propeller stays submerged. Steps to measure transom or bow height. What shaft length do those of you in the know recommend for a.

Place the trolling motor on the ground. Check out our complete line of trolling motors with shaft lengths ranging from 24. 24062020 Shaft length is of key importance because choosing the incorrect length can cause your trolling motor to cavitate and lose thrust.

16072020 The stock Motorguide that came with mine is a strikingly short 39 inch shaft I read online that the shaft length is measured from the bottom of the trolling motor head to the top of the actual motor housing in other words just the actual shaft. 14 posts Trolling Motor Shaft Length Trolling Motor Shaft Length. 07042020 If in deep swells chop like ocean fishing can present or maybe one of the great lakes go with the longer 60.

To get the correct length if you have a transom trolling motor the general rule is that the top part of the motor should be submerged 12 inches. In other words the centerline of the motor and the prop shaft should be about 12-18 inches below the waterline depending on the make model and dimensions of the trolling motor. To determine the right length for your boat measure the distance from where the shaft is mounted on the deck or the transom to the water.

12082020 Adhere to the following steps to measure your motors shaft length. Calculating the Correct Shaft Length A trolling motors ideal propeller should be at a depth that keeps about 6 inches of water above the blades. You also want to prevent the prop from coming out of the water during.

You wouldnt be able to stand and operate the TM big boat wakes may pull the prop out depending how high you adjust motor. The shaft length youll need to keep the motor head submerged at the appropriate depth is at least 35 inches. SHAFT LENGTH GUIDE Looking for a durable trolling motor for your boat.

This length gives you efficient propulsion without being so long that you hit the bottom in shallow water. 07012018 Trolling Motor Shaft Length.

Pin On Trolling Motors Marinewaze