Trolling Motor Foot Pedal Stiff

The tension will loosen if the pedal is misused or abused. It has always been a little tough when it is on 100 but never on 40 until recently.

The Garmin Force Trolling Motor Is Here Trollingmotors Net

These pedals are pretty crappy from my experience as Ive had to circuit boards go out in 5 years.

Trolling motor foot pedal stiff. Exhaust pipe and had it bent up to give me a good handle and also be strong enough. Some other foot pedals have left and right sides that can be depressed to steer and some have separate speed dials you move your foot to when you want to go faster or slower. Lee in Texas 8774233 040113 0325 AM.

For many years the Ultrex has been the reference model not just for other Minn Kota trolling motors but the whole industry in general. I had that problem on my old MG before they came out with troll perfect. It allows for total hands-free control an extremely valuable tool when angling.

I have a 36v 101 Minn Kota foot operated trolling motor on my Triton. 21062006 When you set the Minn Kota at the highest speed you do run into torque issues but the pedal isnt as difficult to move at least in my experience. After reading some of the responses here Im not so sure now.

That can create all new issues. Minn Kota Ultrex trolling motor repair the Minn Kota Ultrex Circuit boards going bad is mostly blamed on that or the foot control sensor on the Minn Kota Ul. 28012009 Posted January 26 2009.

29062020 Jun 29 2020. MotorGuide Tour Pro - Adjusting Foot Pedal Tension. 24072010 The only adjustment to the cables will just take the slop out of the pedal.

23082011 1 Make sure the pedal is not so far to the front of the bow that it is causing a sharp bend in the steering cable where it enters the foot pedal. On my third pedal. 16102019 Definitely try cleaning it first.

Some trolling motor models only have a Constant. I control the troller by a toggle switch at the handle. HELP Please - Motor Guide Trolling Motor Hard to Operate Re.

Control switches on the foot controls usually placed on the sides or ends. The good news is that it is a known issue that an authorized dealer can easily resolve. MotorGuide Tour Pro - Adjusting Foot Pedal Tension - YouTube.

Unfortunately some customers received their trolling motors with a faulty sensor board in the foot control pedal. About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy. It works y pushing the handle forward and pulling it back as if your foot was doing it.

Recently went to a lake and accidentally bent the shaft of the trolling motor. 09112008 I purchased a pro crappie 175 new in 2006. The unit is probably 10-12 years old.

31032013 Could be at either end foot peddle or at the head of the trolling motor. Cable pullys pivots of pedal etc and lubricate them all with WD-40 or CRC something like that in a spray. Apply more or less pressure to go faster or slower.

What should I use to lube with. Need a little help with a foot pedal on a Minn Kota trolling motor. Before I order a new one I thought I would check to see if there is a sensitivity adjustment or cleaning that I should do.

However the Motorguide I owned came with a used boat. These can be depressed by simply pressing them in with the end of your shoe or toe. Mainly because I could never get a feel for where the motor was pointed.

You can cast rig and land fish while using the foot pedal to steer and control your boat. If you take it apart and manually press down on the connection when attached to the trolling motor you will easily know if it is a circuit board issue or needs to be cleaned. Thread starter Jeff Cozadd.

01022003 Trolling Motor Electric Steer vs. In some cases you rock the foot pedal forward or backward to turn the engine left or right. I assumed that the pedal was difficult to operate because it was worn out.

I had one of the electric foot pedals and didnt like it. This action will cause the trolling motor to turn on and begin moving the boat. Good Luck on your repair.

The foot control has been very stiff the last couple of trips out. But cant because of the stiff cableWith the electric control this would be an easy thing to do because of the flexable wire. Depress either the Constant.

If they are pull the foot pedal two screws usually and turn over and lay it on a towel so you can see all the lubrication points ie. I took the bottom bearing collar loose and pulled down on the shaft while forcing the collar up as tight as I could before tightening it back down with an allen wrench. Make sure the cables are on the pullys.

I replaced the foot pedal and cord about 6 years ago so no issues until recently. I have had two trip robbing issues with the trolling motor. Took a piece of 1 14.

Change the direction it is rotated and see if that helps. Safety How YouTube. 2 The head of the trolling motor should be rotated such that the front of the head is pointing to one side or the other not from front to back.

1This summer while docked on Taney at Lilleys I started out fishing one morning ready to hit the first few hours and get in. It comes with a motor guide 46 thrust trolling motor foot operated. My handle after bending it is just about perfect height.

20102017 The foot pedal is used to control the prop angle and adjust for steering and speed. There is a main roller bearing that is located below the head of trolling motor might want to check it to.

Foot Pedal Corded Ulterra Rt Ulterra Minn Kota Motors