Trolling Motor Transducer Cable

Use a zip tie here to hold the cable close to the motor using the hole you drilled. Deck Saver View Deck Saver.

Pin On Bargains Delivered

Use a nylon wire tie every 4 to 6 inches.

Trolling motor transducer cable. Keep cables away from trolling motor pinch points and generally lower electrical interference picked up by todays sensitive transducers. This area is more of connection point for the motor housing. Routing transducer cable on powerdrive trolling motor katman do said.

If you have a bow mounted trolling motor leave some slack in the transducer cables. Route the transducer cable around the trolling motor housing and fasten it to the bottom of the trolling motor shaft with a nylon wire tie. Aluminum CNC machined clamps hold the poly tube and clamp to the trolling motor.

Cable Management Systems View Cable Management Systems. Cable save R gives you a way to protect the cable from getting chewed up on the trolling motor. Assembling the Trolling Motor Mount 1.

If the trolling motor is a bow mount be sure to allow enough slack in the cable to allow depth adjustment. If you run a transducer on the new stile composite shaft trolling motors this is the way to protect the cable. Axiom RV and Axiom PRO 25-pin to 9-pin CPT Transducer Adapter.

Two people left reviews about only being able to fasten the transducer cable to only the top and bottom of motor. Dont let go of the transducer cable. Try to keep the depth finder power cable away from the trolling motor power cable when rigging.

10072018 When routing your transducer cable meet the trolling motor frame at the point where the trolling motor pivots then secure the cable to the trolling motor the remaining way down the shaft. Continue clamping the transducer cable by attaching a nylon wire tie every four to six inches. Route the transducer cable alongside the coil cable using the cable clamps to.

Transducer cable hides inside the poly tube for protection. Feed the transducer cable completely through the square hole in the shaft cap. The grommet is split on one side to make it easy to install on the cable.

Ninja Grass Blade View Ninja Grass Blade. The stow-away locking arms invite the transducer cable to numerous ways to become entangled. Stabilizer Brackets View Stabilizer Brackets.

1 keep the external cable from getting caught up or getting hit by the propeller 2 prevent cable damage 3 to keep the transducer cable away from the trolling motor shaft and 4 to line up the cable so that it doesnt get caught on the trolling motor. CPT-100DVS CPT-120 etc on the Axiom RV and Axiom PRO RVX MFDs. MG recommends one of their models winternal transducer.

Route the cable through the cable exit so the cable is on the top side of the trolling motor housing when stowed. 03032017 The purpose of the kit is to. I have a minnkota 70 with autopilot and would like to mount a transducer to the bottom of the motorproblem is how do i run my wire with the motor slidind up and down the mount to deploy it and also it turning around while steering.

Secure the cables to the bottom of the trolling motor shaft by using a nylon wire tie. Each cable clip also has a unique cavity molded into it that is designed to carry a. DuraSafe Trolling Motor Lock for Minnkota Ultrex View.

10042005 The metal there is kind of a triangle shape on the front side of where the shaft connects to the bottow head of the trolling motor and is only a 14 inch thicknot through the actual housing of the motor. If your trolling motor is a bow mount then dont forget to allow enough slack in the cable. Prop Nuts View Prop Nuts.

Once installed the Ashmore Marine Trolling Motor Cable Keeper Kit gives you piece-of-mind that your transducer cable will no longer have the ability to fall between your trolling motor and base which could cause damage or cut your transducer cable in half. NOTICE Do not cut the transducer cable. Lowrance Trolling Motor Transducer Mount View Transducer Mount.

Poche Wedge View Poche Wedge. Thanks for any info. Fishing Specialties offers transducer to downrod mounting assemblies for all of todays transducers and the extension of the transducer cables through the downrods to make cable management a breeze.

Then take out a nylon wire tie and tie the transducer cable at the bottom of the trolling motor shaft. Tighten the clamp with a flat-head screwdriver. This will allow you to change the trolling motors shaft length as needed.

With the Motorguide Wireless Trolling motor the design makes it a challenge to mount an external transducer. 37 out of 5 stars. Place the mount on your motors housing make sure the transducer is far enough from the prop.

This adapter cable allows for the use of DownVision transducers eg. If you find that interference is still present then you might try using a separate small 12 volt battery to power the depth finder and retest. Push from the outside to secure the square grommet in the shaft cap.

After some mock-ups decided on a unique way to. It is also recommended that the excess length of power and transducer cables not be coiled. I guess that answers my original post.

Run the transducer cable up the motors shaft secure it in place with cable. Dont worry about all the wires being aligned down the shaft --Routing the transducer cable down the trolling motor shaft is a necessity and typically not. Using the 8 mm M4 screws and 4 mm star washers attach the trolling motor mount to the transducer.

Keep attaching more wire ties every six inches or so as you move the cable up the shaft. Install the grommet on the transducer cable. Trolling Motor Transducer Mount.

It also allows for the use of the CPT-S on the Axiom PRO S MFDs. 04062012 As Im looking up and pondering buying a Minn Kota PDv2 with the Universal Sonar so I dont have to run a transducer cable I start to read reviews of my trolling motor on Bass Pro. 04122019 Most anglers that use an electric trolling motor and use it often have some sort of depth finder mounted on the boat as wellOften it is desirable to have the transducer mounted on the trolling motor but this can be a difficult taskIt is important that the transducer and the routing of the cable does not interfere with the trolling motors operationYou must route the cable so.

Route the transducer cable around the trolling motor housing. Installing the Transducer on a Trolling Motor. Attach the transducer to the mount.

MotorGuide MM309922T 8-Gauge Battery Cable and Terminals 50-Amp Manual Reset Breaker Trolling Motor Surge Protection Red One Size.

Pin On Electronics Car Vehicle Electronics

Raymarine E66010 Transducer Extension Cable 16 39 For Dsm30 300 Extension Cable Transducer Cable

Pin On Kayak Trolling Motor

Raymarine Transducer Adapter Cable F Dsm30 Dsm300 Boat Parts For Less Transducer Adapter Cable

Garmin Gt8hw Tm Plastic Tm Or Trolling Motor Transducer High Wide Chirp 150 240khz 250w 8 Pin 010 12401 00 Transducer Trolling Motor Garmin

Humminbird Ad Xtm 9 Trolling Motor Adapter F Xnt Transducers Trolling Motor Humminbird Transducers

Humminbird Xtm 14 Hw Mdi T Mega Di Dual Spectrum Chirp Trolling Motor Transducer W Temp F Solix 710291 1 Trolling Motor Humminbird Trolling Motor Mount

Humminbird Xtm 9 Di 25 T Trolling Motor Dualbeam Down Imaging Transducer In 2021 Humminbird Trolling Motor Mount Transducer

Pin On Products