Trolling Motor Transducer Cable Routing

With electric trolling motors. A must-have for every bass boat the Ashmore Marine Trolling Motor Cable Keeper Kit is the perfect way to keep your electronic cables protected and organized.

Minn Kota Ulterra Si Di Transducer Mounting Youtube

Application Notes Electronic Components Datasheet PDF Search Engine.

Trolling motor transducer cable routing. Δ Position the transducer on the underside of the motor housing with the front of the transducer facing away from the propeller. 10072018 When routing your transducer cable meet the trolling motor frame at the point where the trolling motor pivots then secure the cable to the trolling motor the remaining way down the shaft. 1 4 2 4 3 4.

-Minn Kota Ultrex i-Pilot Link Trolling Motor. Position the transducer so it is parallel to the bottom when in use. Route the transducer cable to the installation location of the.

18022010 The transducer cable can be routed down the starboard side of the boat and generally the cable is shielded so it doesnt matter if it runs with engine wiring. Besides the only interference causing wire in the engine harness is the kill switch and it has low voltage pulses on it which will not bother anything. The trolling motor is deployed or stowed.

Use cable ties not included to secure the transducer cable. Next carefully drill a small pilot hole at the base of the shaft and then step it up a size to a drill bit slightly larger than the transducer cable. You must avoid routing the cable where it is pinched when.

Ad FullText Online Chat BuyNow. Take the top off slide the shaft out of the mount insert the transducer cable through the mount put the shaft back through the mount with the cable in the groove. Route the transducer cable alongside the coil cable using the cable clamps to hold the cables together.

Δ Confirm the transducer cable is correctly routed through the cable slot on the mounting. 04062012 Posted March 31 2012. Route the transducer cable.

Route the transducer cable through the mount base alongside the coil cable using the cable clamps to secure the cables to the base. To avoid damaging the power and transducer cables when deploying and stowing the trolling motor and to avoid interference with the GPS and heading sensors in the motor you must route the cables through the right starboard side of the. You may want to open the head unit at this time also as you will need to fish the transducer cable into the head and out the grommet at the bottom.

Δ Confirm the transducer is oriented in the trolling motors direction of travel. 01032012 It is very easy one or two screws. Use a zip tie here to hold the cable close to the motor using the hole you drilled.

Or other sources of electrical interference. Route the transducer cable. Use some silicone caulking lightly in a few spots along the shaft to hold the cable in the groove Link to post.

04122019 With the Puck transducer mounted you now need to route the cable up the motor shaft down the motor bracket and to the back of the depth finderFoot control trolling motors provide the most challenge when routing the cableAll of the motors movements make it hard to keep the cable from being pulled crushed or cutRefer to the images here to help in the routing of your cable. I have read that its not reccomended to run the transducer cable along the cable steer shroud down to the foot control Due to interference. I have seen some distant pictures of a way you can run the transducer cable up the trolling motor.

I am looking for help on how to route my transducer cable on my motorguide trolling motor. Attach here with zip tie or electric tape. Cable Keeper 3 Cable Clips Stainless Hardware.

A little slack wont hurt anything. Place the transducer mount against the body of the trolling motor with the narrow end of the transducer pointed away from the propeller. 10042005 This area is more of connection point for the motor housing.

Httpsgooglxr43RL-Humminbird Ultrex Trolling Motor 360 Imaging. Then you put the cord up through the handle you use to let the motor down in the water and run up to the top head of the trolling motor. How do I run the transducer table without having it pinch between the mount or bind up on the trolling motor shaft when deploying and storing.

Dont worry about all the wires being aligned down the shaft --Routing the transducer cable down the trolling motor shaft is a necessity and typically not a problem because the power cables. Δ Align the slot in the mounting bracket with the skeg of the trolling motor. You should avoid routing the cable close to electrical wires.

Chartplotter while taking these precautions. Secure the hose clamp around the body of the trolling motor and tighten the hose clamp. Cable Keeper 3 Cable Clips Stainless Hardware.

27112001 Set the trolling motor in the deepest operating position then either tape or tie wrap the transducer wire to the motors shaft. When you retract the motor watch so the cable doesnt get pinched in the motors bracket.

How To Mount A Fish Finder Transducer To A Trolling Motor Inc Minn Kota