Motorguide Trolling Motor Prop Removal

Persistence and versatility are the defining characteristics of great fishermen and great trolling motors. If you cannot get the prop off do not take the plastic nut off all the day.

Pin On Products

Servicing installing or removing motor components.

Motorguide trolling motor prop removal. This kit includes the propeller wrench as well as a spare propeller nut and 2 propeller pins. Thread starter John Lowe. Only tighten the propeller nut anode a 14 turn past snug 25-35 inch lbs.

The wrench also provides storage for the extra pins. Also check the propeller and propeller shaft remove any debris. Oct 8 2010 1 I need to remove the bow mount on my boat which is a 1997 Nitro 700LX.

22042017 I have an older motorguide 71 lb trolling motor. I think I broke the shear pin yesterday in some mud since the shaft spins but the prop does not engage. Instead of trying to figure out which sized trolling motor prop is compatible with your motor you can focus on selecting a prop that matches your needs.

I am actually going to replace the entire cord with plastic covered 18 Inch steel wire clevised onto the spring latch. This will give you something to put your thumbs on. But if your feeling antsy just remove the bolts under the prop to gain access.

View parts diagrams and shop online for COMPLETE TROLLING MOTORMODEL T34 12 VOLT parts 2004 MotorGuide 12V MOTORGUIDE 960010014. I can spin the shaft and spin the prop in opposite directions by hand. The wrench is designed for fast and easy removal and re-installation of a propeller nut.

If the prop is struck grasp one blade with one hand and tap lightly on the backside of the opposite blade with a rubber mallet. Always unplug your Xi Series trolling motor from the 362412V DC port or trip your trolling motor power breaker at the end of the day before charging. Do not use the main engine battery to power the trolling motor.

Also keep note of how the bearing look and where they are placed in the housing. 09112008 Then you can remove the black cover for the mechanism by removing two loctited screws under the motor mount and retie the cord to get by for the day. Joined Aug 26 2010 Messages 58 Reaction score 0.

Tracker Boat Owners Forum. Im trying to remove the prop nut with the prop wrench but the shaft which I assume is threaded also spins with the nut. 09122015 One of the great thing about MotorGuide trolling motors is that nearly all of their lower motor units are standardized at 35 which makes changing or upgrading your prop incredibly easy.

Save up to 100 on qualified motors purchased between March 1 - June 20 2021. MotorGuide freshwater models provide reliable performance for a wide range of fishermen boats and fishing styles. Start date Oct 8 2010.

Offering discount prices on OEM parts for over 50 years. The bottom side of the deck and tighten securely. Help Support Nitro.

CHECK YOUR ROPE FOR WEAR. Do make sure the foot-pedal is secured and the motor. Over tightening can damage the propeller.

Do disconnect the power from the motor when replacing the prop removing debris around the prop charging batteries putting your boat on a trailer or when the motor is not in use. Watch this video for a step-by-step example of how to replace a prop on your MInn Kota Trolling Motor. 16082008 Best answer is to let a pro take care of it.

11102010 Remove Motorguide Trolling Motor Mount. 10012018 Please follow this instruction sheet for correct removal of the propeller. MotorGuide has been dedicated to engineering and manufacturing innovative trolling motors.

Just make sure you know how the brushes fit over the armature when you are disassembling it so they can go back together the same way. Disconnect the trolling motor battery from the main engine battery if equipped. Battery Type The recommended batterys 12 volt Deep Cycle battery with at least 105 ampere hour rating or higher.

Your Xi Series motors circuitry and onboard components need an opportunity to reset to perform optimally. Standard Practices and Procedures When installing or removing this trolling motor follow these guidelines. If you fish grass weeds lily pads etc.

I ran up into a solid mat of hydrilla this past week on multiple occasions and not once did I have to lift the trolling motor out of the water to clean the blades. EASY TO CHANGE IF PROP IS UP INTO THE BOAT. DC motors are fairly simple.

Grab the blades then put you thumbs on the plastic nut and squeeze. Pull the propeller straight off. It is recommended that you remove the propeller after every use to inspect for fishing line and weeds.

The replacement propeller nut has a brass insert for sure installation and reliable long-term service. FAST 495 shipping available. You will hear it pop then take the plastic nut off and remove the prop.

Quick-Release Bracket Composite WhiteThe Quick-Release Bracket provides quick installation and removal of MotorGuide Xi5 trolling motors as well as competitive electric steer motors. While holding the propeller blade use The MotorGuide PropNut Wrench to loosen and remove the propeller nut. The problem is that the mount uses.

7 Lift the motor and mount out of the box turn the mount upri ght and and lay. It on a flat surface. The grounds for the main engine accessories and your trolling motor are connected to the same terminal.

6 Remove the packaging material in the bo x from around the trolling motor. Circuit Protection MotorGuide recommends installing a 50 amp manual reset circuit breaker in the trolling motor. Loosen the moun t locking knob located at the back of.

Then you need this prop. John Lowe Well-Known Member. 07092009 I tried out the new MotorGuide Safari prop this weekend and want to give you my impressions of it.

IMPOSSIBLE IF DOWN IN THE WATER WITHOUT REMOVING MOTOR. Do not power-wash your trolling motor.

Motorguide X3 Trolling Motor Freshwater Foot Control Bow Mount 70lbs 45 24v