Trolling Motor Wire Through Deck

The superior electric current carrying capacity of the. 26072020 Then made the conduit bend 90 degrees to the left under the top deck inside the anchor locker protecting it from rubbing.

When The Ranger 2310 Bay Ranger Is Outfitted With A Trolling Motor The Plug For The Unit Is Inside The Anchor Locker Notic Ranger Boats Trolling Motor Ranger

Connect a connector cable to the positive terminal of battery 1 and to the negative - terminal of battery 2.

Trolling motor wire through deck. Trolling motor install on Deck boats plus front mount fish detector Tahoe 216 OK then a little more work. One of the bolts for the QRB doesnt go through the boat deck - just the plate. Figured I post yet another trolling motor installation.

Make sure that the trolling motor is switched to the off position or speed selector set to 0. Extension Wiring - Since the power leads on trolling motors are only 3-5 feet some installations will require additional lengths of wire to reach the batteries. I have been away from this forum for quiet a while.

If a model is missing the Add to Cart button it is only available through an Authorized Dealer. I suspect the same was used for your model. I have always used Motor Guide so my setup will be as such.

I did the same thing in the console making it route around the console pan. Thanks for the quick replies. However there are certain exemptions to this rule.

Use a quality plug Marinco or Battery Tenders new one. Then you will need to attach a quick-release trolling motor bracket for your trolling motor to the deck you have just made. 25052019 If you do not need to unplug your motor then you might be replacing the plug with one set of terminal blocks to connect your trolling motor power wires and extension power wires.

09012007 Drill about a half inch hole through the deck where the inboard end of the slot in the bowsprit exposes the nose end of the deck. This is where youll run the wires from the trolling motor to the batteries. 18042019 The boat is a 1998 1720.

I installed it on my 16 last year and it worked out fine. I put mine in the port side back near the transom and rn the wires so I could put the battery just forward of the mast support pole. I had to 5200 the grommet in place because the deck was to thick to install the grommets backing nut then I let it dry for 24hrs before feeding the 8ga wires through.

I built a trailerable house boat then sold it and stayed out of boating for a year or so. The other three go through the plate and the boat deck. 11052020 As far as the aluminum base I used it because the trolling motor is extended beyond the side of the bow so the shaft wont hit the side of the boat when deployed.

Just had a though after reading several post about trolling motors on the 1720. I pushed the wire bundle through with some windex making it pull super easy. I have the wire routed in conduit now.

05122019 Screw the plywood to the 2 by 4s with heavy-duty wood screws. 30112014 I prefer the plug for a trolling motor setup. Place your battery switch but you do not need to fasten it securely until you connect the wiring.

Many of our motors are temporarily sold out. 02112018 Remove -inch of the wire coating on the trolling motor wire thatll plug into the back of the new receptacle and both the negative and positive power leads from the trolling motor itself. I was hesitant to cut the trolling motor wire to install the adaptor but all turned out fine.

Wire in series only as directed in wiring diagram to provide 48 volts. By using the 12-volt table below you will be very safe with your wire gauge selection for 24-volt or 36-volt system. Now I have a used fishing pontoon.

Use a quality corrosion spray after every few uses. Make sure to keep the power off when not in use this will drastically cut down on the corrosion. If MinnKota youre going to have to figure it out.

The ConnectPro trolling motor plug and receptacle system is a revolutionary concept in trolling motor DC connections. First if youre thinking motor guide trolling motors some of these will bolt directly too one. I saw some on Craigs list that appeared to have a thru the deck trolling motor.

21082019 I drilled a hole in the deck for a rubber grommet to wire the trolling motor to the batts. You can find the specifications for permissible wires in the regulations. Through hull extension fittings for trolling motor.

If a model is missing the Add to Cart button it is only available through an Authorized Dealer. According to the regulations a wires minimum size should be 16 AWG. I went with the Motor Guide 80lbs trust with the 60 shaft with the.

The Marinco does not hold water unless you silicone the thru wire holes. Usually you will need to attach four bolts from the bottom half of the bracket to the deck and four bolts from the top of the bracket to the motor. Manufacturers of trolling motors tend to come up with a guide for wire gauge to use but they do this for the voltage rating of the motor ie 12V 24V and 36V would have different catalogs.

23052013 Jun 10 2003. Factory TM wiring in 2002 was three conductors of 6awg. Allows 6 gauge wire connection to ConnectPro receptacle Corrosion resistant plated brass electrical components.

24022020 Due to the fixed insulation rating of the wire the value of current allowed decreases when many wires are in a bundle. Measure the distance from the trolling motor mounting location to the batteries and determine the length of wire needed. In this picture the white tube running on top of the tank thats the wire chase running to the stern for.

Many of our motors are temporarily sold out. I pretty much went with member MZBHAVN Minn Kota post verbatim but added a few additional steps that I ran into that might assist others. Connect the trolling motors power leads into the male end the plug and the battery leads to the female end the receptacle.

Minn Kota 10 Ga Battery Lead Wire Assembly 2992521 Northland Marine

Amazon Com Minn Kota 1865107 Mkr 20 Trolling Motor Quick Connect Plug Marine Battery Accessory Black Automotive

Boat Projects Jon Boat Project Boat Diy

Motorguide Trolling Motor 70 Lbs 24v Steering Cable Came Loose From Steering Rack Gear In The Powerhead R Trolling Motor Motorguide Trolling Motor Cable