Trolling Motor Transducer Cable Mount

03032017 The purpose of the kit is to. It fits motors of varying sizes such as 3-14 inches 3-58 inches and 4-12 inches.

Humminbird Xtm 9 Di 25 T Trolling Motor Mount Transducer 710234 1 In 2021 Trolling Motor Trolling Motor Mount Transducer

In addition the quick movements of a trolling motor mounted transducer tend to ruin imaging from these expensive units.

Trolling motor transducer cable mount. Installing the Transducer on a Trolling. Cable save R gives you a way to protect the cable from getting chewed up on the trolling motor. Or Less top Rail or Gunnel.

Use some silicone caulking lightly in a few spots along the shaft to hold the cable in the groove Link to post. Protects your external transducers cables when mounting on electric drive trolling motors. Ninja Grass Blade View Ninja Grass Blade.

It also works well with transducers from other major manufacturers. Place the mount on your motors housing make sure the transducer is far enough from the prop. For example if you are able to mount a transducer with Xi5 it will either catch the cable in the mechanism tearing it or potentially spin until the conductors rip.

Installing the Transducer on a Trolling Motor. If you run a transducer on the new stile composite shaft trolling motors this is the way to protect the cable. Cable save R gives you a way to protect the cable from getting chewed up on the trolling motor.

Next you need to connect the cables to the trolling motor bracket through the motor shaft. Trolling Motor Transducer Mount. More Detail at Store.

50 cm cable tie around the body of the trolling motor but do not fully tighten the cable tie. 04062012 Posted March 31 2012. Thats correct Wade you can mount most type through the hull although not ideal.

Assembling the Trolling Motor Mount 1. 04122019 Most anglers that use an electric trolling motor and use it often have some sort of depth finder mounted on the boat as wellOften it is desirable to have the transducer mounted on the trolling motor but this can be a difficult taskIt is important that the transducer and the routing of the cable does not interfere with the trolling motors operationYou must route the cable so. If you run a transducer on the new stile composite shaft trolling motors this is the way to protect the cable.

Use a nylon wire tie every 4 to 6 inches. With transom mount motors no slack is needed. Garmin 010-01550-00 Striker 4 with Transducer 35.

March 26 2004 at 851 pm 298433. MG recommends one of their models winternal transducer. 27042021 Steps to mount TotalScan transducer.

Each cable clip also has a unique cavity molded into it that is designed to carry a. Then tie your cable over the hose clamp and ensure that the transducer is pointing down straight. Lowrance Trolling Motor Transducer Mount View Transducer Mount.

Protects your external transducers cables when mounting on electric drive trolling motors. Tighten the clamp with a flat-head screwdriver. 48 out of 5 stars.

If your trolling motor is a bow mount then dont forget to allow enough slack in the cable. After some mock-ups decided on a unique way to. Poche Wedge View Poche Wedge.

First stretch out your cables beforehand to avoid any bends on the cables. Take the top off slide the shaft out of the mount insert the transducer cable through the mount put the shaft back through the mount with the cable in the groove. With the motor in the deployed position route the transducer cable through the channel along the right starboard side of the mount.

A transducer on trolling motor is just a bad idea. Route the cable through the cable exit so the cable is on the top side of the trolling motor housing when stowed. Run the transducer cable up the motors shaft secure it in place with cable.

Position the mount gasket on the curved top of the transducer mount. Dont let go of the transducer cable. If the trolling motor is a bow mount be sure to allow enough slack in the cable to allow depth adjustment.

Route the power cable through the channel above the transducer cable. Place the transducer mount against the body of the trolling motor with the front of the transducer pointed away from the propeller. Then take out a nylon wire tie and tie the transducer cable at the bottom of the trolling motor shaft.

With the Motorguide Wireless Trolling motor the design makes it a challenge to mount an external transducer. GPS Fishfinder with Chirp Traditional Transducer. With cable tieselectrical tape and just paying attention to your ducer cable mounting it on the motor is usually not a problem.

DuraSafe Trolling Motor Lock for Minnkota Ultrex View. Once installed the Ashmore Marine Trolling Motor Cable Keeper Kit gives you piece-of-mind that your transducer cable will no longer have the ability to fall between your trolling motor and base which could cause damage or cut your transducer cable in half. Secure the 20 in.

Using the 8 mm M4 screws and 4 mm star washers attach the trolling motor mount to the transducer. The stow-away locking arms invite the transducer cable to numerous ways to become entangled. Features high quality and allows you to mount the transducer on both bow and transom trolling motors.

Pro Controll EZ Mount II Replacement Bracket Allows You to Mount a Hand Controlled trolling Motor on The Bow of Your Jon Boat. Fits Boats with a 3. 09092020 Route the transducer cable around the trolling motor housing.

06102020 MKR-15 transducer mount kit by Minn Kota. Continue clamping the transducer cable by attaching a nylon wire tie every four to six inches. Cable Management Systems View Cable Management Systems.

It is suggested that you tie the cables in. To determine the right starboard side of the mount stand in a location where you can read the information on the display panel. Attach the transducer to the mount.

Deck Saver View Deck Saver. Prop Nuts View Prop Nuts. 1 keep the external cable from getting caught up or getting hit by the propeller 2 prevent cable damage 3 to keep the transducer cable away from the trolling motor shaft and 4 to line up the cable so that it doesnt get caught on the trolling motor.

Humminbird 710205-1 XTM 9 HDSI 180 T DualBeam HD Side Imaging Trolling Motor Mounted TransducerBlack. Stabilizer Brackets View Stabilizer Brackets.

Pin On Electronics Car Vehicle Electronics

Minn Kota Powerdrive V2 Transducer Installation Youtube Transducer Minn Kota Installation

Ad Ebay Humminbird 710198 1 Xnt 9 20 T Tm Transducer 83 200 Khz In 2020 Transducer Humminbird Trolling Motor Mount

Pin On Alimongo

6 Black Blue And Orange 8 Pin Transducer To 12 Pin Sounder Adapter Cable With Xid In 2021 Transducer Garmin Sounders

Humminbird Xtm 9 Hdsi 180 T Side Imaging Trolling Motor Transducer 710205 1 Humminbird Trolling Motor Trolling Motor Mount

Discounted Garmin Transom Trolling Motor Mount Dual Beam Transducer 010 10249 20 010 10249 20 010 10249 20 Trolling Motor Trolling Motor Mount Transducer

Humminbird Xnt 9 Hw T Helix Dual Spectrum Chirp Transom Mount Transducer W Temp 710274 1 Humminbird Transducer Helix

Humminbird 740182 1 Ad Mtm Hw Msi Mega Si Trolling Motor Adapter Brac Trolling Motor Humminbird Motor