How To Set Trolling Motor Depth

Motor Guide Depth Adjustment Collar w Knob. Add an additional 5 inches to the sum above.

How Deep Should My Trolling Motor Be In The Water Anchor Travel

Not for use with 125.

How to set trolling motor depth. Click to see full answer. It would read apporx 3 ft shallower than my graph on the transom when it. In other words you want the centerline of the prop one foot or more below the surface of the water.

Any trolling motor regardless of type or manufacturer recommends selecting a shaft length that is equal to the distance from the bow to the water line plus one foot. The way I do it is by putting the top of the prop a few inches under the surface loaded boat then going from stop to full if it doesnt cavitate or suck air Im good. Turn them clockwise to the maximum.

27022020 Always Go Long. 2 Mark holes to be drilled through the anti-cavitation plate. To Adjust motor depth - The depth fo the motor can be adjusted up and down by simply loosening the depth collar tension knob located on the column.

In rough water you will want it as deep as you can go. The first is to deploy it to a specific distance then troll up a gradual shelf or edge until it starts dragging bottom. If your trolling motor has controls that you operate from a standing position the shaft will have to be even longer because more of it will be above the boat.

Use the mount itself as a template for this. Heavy glass bass boats dont tend to lift in waves as high as a aluminum boat set the depth so it doesnt cavitation in normal wave conditions or boat wakes. 16042003 From page 13 of the MotorGuide Tracker series manual.

If the shaft ends up being a bit too long you can always adjust the shaft depth upward with the depth collar adjustment found on nearly all trolling motors. With the quick squeeze of a lever. 14042011 If it is a calm day on the water when I launch the boat I will set it so the blades are under by one inch.

Trolling Motor Depth What kind of boat do you have. If youre struggling to decide between two lengths pick the longer one. If its a little tinny probably a 30.

Anything in between the depth really doesnt matter that much. Trolling Depth Trick 1 There are two ways you can determine the exact depthlurespeed relationship of a specific rig. Deep its usually windy with white caps and leave it set.

19012021 Your anti-cavitation plate must run at a depth of at least 13 inches 325 cm below the waterline so that the trolling motor will run at least 6 inches 15 cm below the waterline while in operation. 02062018 Posted June 1 2018. If you have something like mine a 16 glass runabout probably a 36.

Yes some days I add more as I go since it may change as I. Diameter Shafts or Larger. Note the depth and try to crank it in before it snags.

Raise or lower the depth of the trolling motor. Place the Motor Carefully over the Transom. Adjust the height of your Motor Guide VariMax.

Get the measuring tape out and see what length it takes for the prop to be submerged and the tiller to be at a. 01062018 If you set the motor too deep you run a greater risk of hitting objects fouling the prop on weeds and tearing up the prop andor bending the shaft. You should be prepared for the motor to slide down when you loosen the collar.

Adjust the Depth of the Motor. Adjusting the Depth of the Trolling Motor. Loosen the collar at the base of the steering system housing.

Transom-mount trolling motors have usually 2 clamps that are used to hold the motor in place. If there is wave action I try to see how much wave action and added that to the inch. Good depth for trolling motor.

Quick turn of a knob. Adjust the height of your motor with the. But if you pick a shaft thats too short youre simply out of luck.

In shallow water you want it up as as high as you can get it without it hitting bottom. Add an additional 12 inches. - Motor Guide Varimax Series.

31082008 Aug 26 2008. 30032009 it really depends on conditions. 25102008 I would adjust or tighten it and it eventually would always slip deeper so I didnt want to mess with setting the offset since the depth of the trolling motor was going to change.

I like mine set 16-18. Diameter Stainless Steel Shaft. X3 or is it 4.

Move the motor so that it stops halfway between the stowed and deployed positions. The motor should go all the way down until the top of the mounting bracket is flush with the transom.

I Have A 15 Foot Canoe That I Use For Fishing And Would Like To Put A Trolling Motor On It The Kayak Trolling Motor Mount Trolling Motor Mount Trolling Motor

Force Trolling Motor Adjusting The Depth Of The Trolling Motor

Mounting Transducers To Trolling Motors

Mounting Transducers To Trolling Motors

How Deep Should My Trolling Motor Be In The Water Anchor Travel

How Do I Install A Humminbird Trolling Motor Transducer On My Minn Kota Power Drive Terrova Or Ulterra Trolling Motor Humminbird

Get The Right Size Trolling Motor West Marine

Amazon Com Rite Hite Isolator Bolt 8 Pack Ideal For Mounting Trolling Motors Gps Systems And Depth Finders Use For Anywhere A Blind Hole Application Is Required Sports Outdoors

15098 Handheld Remote User Manual Xi5 Wireless Edition Motorguide