Correct Trolling Motor Depth

You also want to prevent the prop from coming out of the water during. Check for proper transducer installation according to the Operations Manual.

What Are The Basic Parts Of A Bow Mount Trolling Motor Dc Trolling Motor

12 24 or 36 volts.

Correct trolling motor depth. Trolling Depth Trick 1. 15012018 Measure down from the mounting surface of the transom or bow to the water level. Repeat this procedure if necessary to set the correct depth for the deployed or stowed position.

Small boats under 14 feet are well suited for electric trolling motors. Remember the general rule is to keep the motor submerged 12 inches below the waterline. Any trolling motor regardless of type or manufacturer recommends selecting a shaft length that is equal to the distance from the bow to the water line plus one foot.

27022020 Always Go Long. There are two ways you can determine the exact depthlurespeed relationship of a specific rig. Determine the motor shafts length.

01062018 If you set the motor too deep you run a greater risk of hitting objects fouling the prop on weeds and tearing up the prop andor bending the shaft. In other words you want the centerline of the prop one foot or more below the surface of the water. To waterline measurement for fishing in rough water.

Batteries Bass Pro Shops Deep-Cycle and Starting 12V Marine Dual-Purpose Battery. Use this measurement and the tables below to find the appropriate trolling motor shaft length. Back to back days of trolling may be a bit tricky since these motors deplete battery reserves quickly.

Note the depth and try to crank it in before it snags. Correct Lake Troll Speed. Even bow mounted motors can be used for slow trolling.

If the shaft ends up being a bit too long you can always adjust the shaft depth upward with the depth collar adjustment found on nearly all trolling motors. To waterline measurement for steering a hand control motor while standing. In order for a 24-volt motor to work it must be run off of two.

TECH TIPS - YouTube. Transducers secured Running lights present and functioning Transom _____ Drive _____ Correct trolling motor installed correctly All drain plugs in boat including Livewell. 14042011 Do trolling motors work betterfastermore efficiently when higher in the water or does it not make much difference.

Current is always the big factor but it shouldnt be too big of a problem. I usually keep mine a little deeper than it needs to be so when the wind picks up I dont have to mess with it. If you are stowing the trolling motor move the motor to the stowed position to check the depth Stowing the Motor from the Deployed Position.

The correct transducers to be used with your depth sounder are listed in your Operations Manual. If you are deploying the trolling motor move the motor to the fully deployed position to check the depth. The first is to deploy it to a specific distance then troll up a gradual shelf or edge until it starts dragging bottom.

I always ran mine at least 12. 07032018 On a 600lb Jon boat you should be just fine with a 55lb motor even after adding the weight of gear motor and people to an extent. But if you pick a shaft thats too short youre simply out of luck.

30072019 Trolling Motor Voltage. Determining the proper trolling motor shaft length is one of the key aspects of finding the right motor for your boat. Use a tape measure and determine the motor shafts length by measuring from the base of the head down to the propeller housing in inches.

Correct Lake Troll Speed. If youre struggling to decide between two lengths pick the longer one. Place the trolling motor on the ground.

It will help ensure that the motors shaft is long enough to keep the propeller submerged at least 12. 10042018 Normally the transducer type is marked on the cable within the first 6 inches from the connector end. Below the water line in your specific fishing conditions.

To make it easier to understand a 12-volt trolling motor is run off of one 12-volt deep cycle marine battery. 12082020 Adhere to the following steps to measure your motors shaft length. In other words the centerline of the motor and the prop shaft should be about 12-18 inches below the waterline depending on the make model and dimensions of the trolling motor.

Next time youre out on the water you can feel confident knowing that your trolling motor is at the ideal depth for your boat and water conditions. A trolling motors ideal propeller should be at a depth that keeps about 6 inches of water above the blades. Most anglers think of trolling motors as a means to reposition boats for casting but even a larger boat outfitted with a trolling motor can use it for trolling.

If youre in the main channel in. Under as well but thats because MK says so in the manual Im gonna try raising it up a bit this weekend if I get out in my boat. Good depth for trolling motor.

Electric trolling motors come in three separate power systems.

5 Best Bow Mount Trolling Motors In 2021 Anchor Travel