Trolling Motor Puck Mount

22012018 Looks like some have the puck mounted close to the edge where some of the bolts can be reached from the outside under the lip on the cap of the boat. Puck Plastic Trolling Motor Mount Transducer Kit for FL-12 and FL-20 Flashers TK-287 by Vexilar Measures.

Amazon Com Marcum Vx Series Trolling Motor Mount Transducer Kit 20 Degree Fishing Equipment Sports Outdoors

Albeit you still need to build up the base under the puck to level it at trolling speeds.

Trolling motor puck mount. Trolling motor install on Deck boats plus front mount fish detector Tahoe 216 And I did have the pucks already mounted. Dealers and builders set them out on or over the edge to free up deck space. Choose the Puck Style if you plan on mounting to an electric trolling motor or for in-hull mounting applications for.

Mounts to your outboard engine saving valuable deck space A great choice for dual-purpose boats or where a traditional installation is difficult Motor speed controlled via wired remote. Puck transducers have a slot for a hose clamp. Buy in monthly payments with Affirm on orders over 50.

Made from Marine Grade Plastic and is CNC Machined for a precision fit. Once the ice fishing season is over its time to shift to the open water. 04122019 With the Puck transducer mounted you now need to route the cable up the motor shaft down the motor bracket and to the back of the depth finderFoot control trolling motors provide the most challenge when routing the cableAll of the motors movements make it hard to keep the cable from being pulled crushed or cutRefer to the images here to.

I have seen a few people do this due to the puck having to be mounted further back on the front deck and that extra inch or two is needed for the TM shaft to clear. Mount that literally leaves nothing more than a smooth puck on your bow. Pre Drilled to accept Most Minn Kota Trolling Motors.

21092020 Minn Kota bow mounts have a puck. Pro Controll EZ Mount Now you can mount a hand controlled trolling motor on the bow of your jonutility boat. I have mine set about 2 inches inside the boat.

When at full power and steered fully port the motor just wants to rip the mount right out of the hull. 13112018 Joined Oct 4 2018. Pro Controll EZ Mount trolling motor mount is a versatile trolling motor mounting bracket that can be used on a boat with a 3.

You need to mount it towards the bottom. 5266 anchor nest mount minn kota mount puck and pin quick mount. Step 3 Select the ITD5709 Quick Mount Anchor Nest Mount if you want to also install your anchor nest.

Allows trolling motor to be quickly removed from and reattached to boat deck Low-profile design attaches trolling motor to top bracket and drops in over deck-mounted puck Composite construction resistant to rust corrosion and discoloration Locking handle can be secured with padlock not included for additional security. Im installing a 112lb 36v Minn Kota Ulterra on my 239FS with a windlass anchor. 05022018 Quick Mount Minn Kota Mount.

Steered via the existing outboard wheel Variable speed motors ranging from 55 to 160 lbs Will it fit your outboard. When I install a trolling motor Ill remember your pictures. Step 1 Select the ITD5506 Quick Mount Mounting Puck.

This was to allow fisherman to remove the motor and still get a cover on. 19012021 An electric trolling motor designed to be mounted on the transom can also be mounted on the bow of a V-hull boat or adapted for backtrolling trolling stern-first by taking out the screw and nut at the base of the motors control unit rotating the control unit 180 degrees and then replacing the screw and nut without damaging the motor wires. This offset install has been an epic fail.

Make sure to use stainless steel hose clamps. I see theres a plate glasses in that can be drilled and tapped. 16062020 I think the quick release is hanging off extra because they used 4 mounting bolts instead of the 6.

Minn Kota Trolling Motor Part - CAM PUCK - 2228412. It looks like the puck could have been installed a little bit back from the rub rail but its difficult to know if the trolling motor shaft would have cleared the rub rail if the puck was back a bit. So ita never in my way.

If you look at the shadow in the pic you can see about where it sits. I tend to forget about the puck when at the helm. WILL NOT FIT ON KAYAKS.

Or less top rail or gunnel. Just wondering what others have done. Others look like the bolts ended up further back with all the bolts ending up on the inside.

See our guide o. Im on my 2nd motor and mounting plate. I fish Galveston and I use the trolling motor 99 of the time when I fish.

Replaces Part Numbers 2228410. Tons of torque on the plate and the fiberglass isnt. 26092019 Here are pictures of the 4 holes drilled to mount the quick release puck the the puck mounted after I installed the 2 bow cleats on my 176 CC and what the boat looks like from a distance without the trolling motor installed.

Locking Pin kit Step 2 Select the ITD5266 Quick Mount Minn Kota Mount if you want to install your Trolling Motor works with Motor Guide Xi5 Trolling Motors andor. So the way I found the right one was to measure the distance between the two pucks. Thanks for the pictures.

If you use 4 bolts you can have the troller sit another 2 to 3 inches in front of the puck. 09092020 The best location to mount the transducer is directly behind the fin of your trolling motor. You need to clamp the transducer with hose clamps around the trolling motor.

Minn Kota Riptide Saltwater Composite Quick Release Bracket Rta 17